series am 1dr -rz 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r9. e 1 of 3 north america only features: ? regulated single output ? 1000vdc isolation ? continuous short circuit protection ? operating temperature: - 40c to +85c ? rohs compliant ? industry standard pinout ? mtbf> 1 , 5 00,000 hours ? sip 7 package m odels single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) max capacitive load (uf) efficiency (%) am1dr - 0503s - rz 4.5 - 5.5 3.3 303 1000 220 55 am1dr - 0505s - rz 4.5 - 5.5 5 200 1000 220 64 am1dr - 0507s - rz 4.5 - 5.5 7.2 139 1000 220 64 am1dr - 0509s - rz 4.5 - 5.5 9 111 1000 220 65 am1dr - 0512s - rz 4.5 - 5.5 12 83 1000 220 66 am1dr - 0515s - rz 4.5 - 5.5 15 67 1000 220 66 am1dr - 1203s - rz 10.8 - 13.2 3.3 303 1000 220 56 am1dr - 1205s - rz 10.8 - 13.2 5 200 1000 220 64 am1dr - 1207s - rz 10.8 - 13.2 7.2 139 1000 220 65 am1dr - 1209s - rz 10 .8 - 13.2 9 111 1000 220 66 am1dr - 1212s - rz 10.8 - 13.2 12 83 1000 220 66 am1dr - 1215s - rz 10.8 - 13.2 15 67 1000 220 68 am1dr - 2403s - rz 21.6 - 26.4 3.3 303 1000 220 56 am1dr - 2405s - rz 21.6 - 26.4 5 200 1000 220 63 am1dr - 2407s - rz 21.6 - 26.4 7.2 139 1000 220 65 am 1dr - 2409s - rz 21.6 - 26.4 9 111 1000 220 66 am1dr - 2412s - rz 21.6 - 26.4 12 83 1000 220 67 am1dr - 2415s - rz 21.6 - 26.4 15 67 1000 220 67 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input volt age and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 5 12 24 4.5 - 5.5 10.8 - 13.2 21.6 - 26.4 vdc filter capacitor absolute maximum rating (100 ms) 5 12 24 7 15 28 vdc no load input c urrent 4 5 ma input r eflected ripple c urrent 20 ma p - p isolation specifications parameters conditions typical rated units tested i/o voltage 3 sec 1000 vdc resistance at 500vdc >1000 mohm capacitance 60 pf output specifications parameters conditions typical maximum units voltage accuracy 2 % short circuit protection continuous short circuit restart auto - recovery line voltage regulation ll ~ hl 0.5 % of vin
series am 1dr -rz 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r9. e 2 of 3 north america only output specifications (continued) parameters conditions typic al maximum units load voltage regulation from 0% to 100% load 0.5 % load voltage regulation (3.3v output) from 0% to 100% load 1 % temperature coefficient 0.02 %/ o c ripple & noise 20mhz bandwidth 50 mv p - p general specifications parameters co nditions typical maximum units switching frequency 50 (variable) khz operating temperature full load - 40 to +85 o c storage temperature - 40 to +125 o c maximum case temperature 100 o c cooling free air convection humidity 95 % rh case material n on - conductive plastic (ul94v - 0) weight 2.7 g dimensions (l x w x h) 19.50 x 7.20 x 9.50 mm ( 0.7 7 x 0.28 x 0.3 7 inches ) mtbf > 1,500,000 hrs dual (mil - hdbk - 217f, ground benign, t=+25 o c) maximum soldering temperature 1.5mm from case for 10 sec 2 60 o c safety specifications parameters agency approvals ce safety standards en 55022, class b iec61000 - 4 -2 iec61000 - 4 -3 iec61000 - 4 -4 iec61000 - 4 -6 iec61000 - 4 -8 also d esigned to meet iec 60950 - 1 pin out specifications dimensions pin single 1 + v in put 2 - v input 4 - v output 5 no pin 6 + v output 7 no pin 19 . 50 ( 0 . 78) 2 . 54 ( 0 . 10) printed face 0 . 50 ( 0 . 02) 0 . 50 ( 0 . 02) 1 . 25 ( 0 . 05) 7 . 20 ( 0 . 28 ) 9 . 50 (0 . 37 ) 9 . 50 (0 . 37 ) 3 . 05 (0 . 12 ) 0 . 50 (0 . 02 ) 7 . 20 ( 0 . 28 ) 0 . 2 5 (0 . 0 1 )
series am 1dr -rz 1 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r9. e 3 of 3 north america only radiated and conducted emissions application circuit: c1 l1 47 0f/100v 12 h note: 1. datasheets are updated as needed and as such, specificati ons are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on l abels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless ot herwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may no t be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate specific safety and regulatory standards o ther the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s standard terms of sale available at www.aimtec.com.
|
